CO2 লেসার কর্তনকারী 150W MDF প্রকল্পের জন্য
এই প্রকল্প দ্বারা কাটা হয় STJ1325-4 MDF লেজার কাটার চার সেট সঙ্গে 150W CO2 লেজার টিউব, যা একই সময়ে চারটি MDF বোর্ড কাটতে পারে।
আপনি কিছু লেজার খোদাই কাটিং কাঠের কারুশিল্পের ধারনা এবং পরিকল্পনা পাবেন CO2 লেজার কাটার, যা লেজার কাঠ কাটার খোদাই মেশিন কেনার জন্য একটি রেফারেন্স হবে।
কাঠ কাটতে লেজার ব্যবহারে উচ্চ নির্ভুলতা, সরু স্লিট, দ্রুত গতি এবং মসৃণ কাটিয়া পৃষ্ঠের সুবিধা রয়েছে। যাইহোক, যেহেতু লেজার ফোকাসড এনার্জি কাঠকে গলিয়ে দেয়, তাই কাটার প্রক্রিয়ার সময় কালো হয়ে যাবে, অর্থাৎ কাটিংয়ের প্রান্তটি কার্বনাইজড হয়। আজ আমরা আপনাদের সাথে কথা বলি কিভাবে এটি কমানো যায় বা এড়ানো যায়।
The 1st thing to note is that if you are cutting thicker boards, it is very difficult not to get black. After my test, it is concluded that the cutting of templates with a thickness of 5MM can be d1 without much blackening, while those above 5MM It depends on the situation. Here's a detailed description of how to make the laser cut wood not black:
Maybe every1 knows that to avoid the carbonization effect of laser cutting, use high speed and low power. This is right, but some are misunderstood. They feel that the faster the better, the lower the power the better, and to reduce blackening, they cut multiple times with fast speed and low power. This is very bad and the carbonation effect may be darker than normal.
Our low power and fast speed must ensure that the wood can be cut through at 1 time. The faster the speed is, the better the speed, and the lower the power, the better. If reducing the power requires multiple cuts, the carbonization phenomenon is actually more serious. Because the part that has been cut through will be burned a 2nd time, the more you cut it, the more serious the carbonization will be.
The part that was cut through the 1st time was burned again during the 2nd cut. The other part, because it was not cut through the 1st time, was not so black.
Therefore, the 1st point to pay attention to is to ensure that it is formed in 1 processing, not secondary processing, to avoid secondary damage.
And fast speed and low power are contradictory, the faster the speed, the more difficult it is to cut through, and the smaller the power, the more difficult it is to cut through. Between the 2 we have to prioritize. In my experience, fast speed is more important than low power. With more power, try the fastest speed you can cut through. Of course this needs to be tested to get the best value.
অবশ্যই, কালো হওয়ার উপর শক্তির গতির প্রভাব ছাড়াও, আরেকটি খুব গুরুত্বপূর্ণ কারণ রয়েছে, যা বাতাসকে প্রবাহিত করছে। কাঠ কাটার সময়, আপনাকে অবশ্যই জোরে বাতাস উড়িয়ে দিতে হবে। একটি উচ্চ-পাওয়ার এয়ার কম্প্রেসার ব্যবহার করা ভাল, কারণ কালো এবং হলুদ হওয়ার আরেকটি কারণ হল, কাটার ফলে উত্পন্ন গ্যাস কালো হয়ে যায় এবং ফুঁটি কাটাকে সহজতর করতে এবং আগুন প্রতিরোধ করতে কাটিংকে সহায়তা করতে পারে।
এই প্রকল্প দ্বারা কাটা হয় STJ1325-4 MDF লেজার কাটার চার সেট সঙ্গে 150W CO2 লেজার টিউব, যা একই সময়ে চারটি MDF বোর্ড কাটতে পারে।
একটি জন্যে CO2 জন্য লেজার কাটার 3D জীবন্ত কব্জা সহ পাতলা পাতলা কাঠের পেনসিল কাপ এবং কলম হোল্ডার? ফাইল বিনামূল্যে ডাউনলোড করুন 3D কলম ধারক এবং পেন্সিল কাপ।
মেটাল পাইপ এবং টিউব লেজার কাটিয়া মেশিন ধাতব পাইপ এবং টিউবের বিভিন্ন দিক থেকে বিভিন্ন ব্যাসের লাইন এবং গর্ত কাটার জন্য ব্যবহৃত হয়।